Template:Launch checklist

When it's possible, the original Apollo documentation is used for the checklists. Steps, which are not possible at the moment, are denoted in grey. Additionally there are checklists in Word file format in the Doc\Project Apollo - NASSP\Check List directory of your installation. Procedural steps in this section are presented in tabular form and in sequence they occure during the mission. The following is a detailed explanation of the columnar data presented in the tabulated lists:

Apollo 15 launch checklistA15_LAUNCH_CHECK

Time	This column contains the mission time the procedure is to be done. Sometimes there's no fixed time when to do a procedure, in that case the time is left out.
Procedure	The procedure is a group of steps or overall tasks involved in performing a complete function or operation. It often consists of controls the astronauts have to toggle or display readings that have to be checked. See CSM panels for more informations.
Panel	The panel number of a particular switch or display for easier panel navigation.
Remarks	Any useful comment. Please notice especially differences to the original function, bugs or other issues.

At T+00:00:00 the Saturn launches automatically. The following tables show the historical launch sequence of Apollo 16AOH2, all other Saturn V missions are very similar. Only the Saturn 1b missions are different, because the Saturn 1b stage has only 2 stages, so there's only 1 staging event. {{ #if: | |

Attention

Please note that all DSKY interaction mentioned in the original documentation cannot be used in Standard mode with the NASSP AGC.

}}

Boost & insertion

{{ #if: | |

Attention

Please note that all DSKY interaction on the last 2 pages above cannot be used in Standard mode with the NASSP AGC. With the NASSP AGC just enter V37 N00E to go to program P00.

}}

Postorbital insertion checks

After SIVB engine cutoff (SECO) the spacecraft is in an almost circular earth orbit, called "Earth Parking Orbit" (EPO). Now the postorbital insertion checks have to be done.

Time	Procedure	Panel	Remarks
00:12:00	Postorbital insertion checks   EDS PWR - OFF MAIN BUS TIE (2) - OFF SECS PYRO ARM (2) - SAFE SECS LOGIC (both) - OFF cb SECS ARM (2) - open TRANS CONT PWR - OFF ROT CONTR PWR DIRECT (2) - OFF BMAG MODE (3) - RATE 2 LV STAGE sw - OFF (verify) DIRECT O2 vlv - CLOSE   C/W NORM - NORM   FC REACS VLVS - NORM H2 PURGE LINE HTR - ON	7 5 8     1     2 7   2   3	Prepares the FC purge check.

SM RCS monitoring check

SM RCS monitoring check   SM RCS PRPLNT tb (8) - gray SM RCS HELIUM 1/2 tb (8) - gray

2

C&WS operational check

C&WS operational check   postorbit_cwsoperationalcheck.gif   A more detailed check can be found in the ???

2

CM RCS lights not working yet.

ECS post insertion config

	ECS post insertion config   PRIM GLY EVAP STM PRESS ind -   0.09-0.14 psi PRIM ACCUM QTY ind - 25-50 % RAD FLOW CONT PWR - PWR PRIM GLY TO RAD vlv - NORMAL (push) RAD PRIM HTR - 1 ECS RAD tb - gray GLY EVAP TEMP IN - AUTO POT H2O HTR - MNA	2       325 2
	CAB FAN (both) - on (up)   O2 FLOW ind - 1.0 lb/hr   O2 FLOW HI lt - on   MASTER ALARM pb/lt - on, push     O2 FLOW HI lt - off   PRIM GLY EVAP OUT TEMP ind - 38-43 °F   RAD PRIM OUT TEMP ind - below     RAD PRIM IN TEMP ind	2     1   2	After a few minutes. After a few minutes.

Fuel cell purge check

Fuel cell purge check   postorbit_fcpurgecheck.gif

3

EPS monitoring check

EPS monitoring check   postorbit_epsmonitoringcheck.gif   A similar check can be found in the ??? section.

ECS monitoring check

ECS monitoring check   postorbit_ecsmonitoringcheck.gif   A similar check can be found in the ??? section.

Secondary water-glycol loop check

Secondary water-glycol loop check   postorbit_secglycolloopcheck.gif

SCS attitude reference check

SCS attitude reference check   This procedure only works with the Virtual AGC.   <img src="../images/postorbit_scsattcheck.gif">

DSKY 1

Extend docking probe

Extend docking probe   postorbit_dockingprobeextend.gif

8 2

<biblio force=false>

1. References

</biblio>