Template:Launch checklist: Difference between revisions

Latest revision as of 12:13, 4 February 2007

At T+00:00:00 the Saturn launches automatically. The following tables show the historical launch sequence of Apollo 16AOH2, all other Saturn V missions are very similar. Only the Saturn 1b missions are different, because the Saturn 1b stage has only 2 stages, so there's only 1 staging event. {{ #if: | |

Attention

Please note that all DSKY interaction mentioned in the original documentation cannot be used in Standard mode with the Simple AGC.

}}

Boost & insertion

{{ #if: | |

Attention

Please note that all DSKY interaction on the last 2 pages above cannot be used in Standard mode with the Simple AGC. With the Simple AGC just enter V37 N00E to go to program P00.

}}

Postorbital insertion checks

After SIVB engine cutoff (SECO) the spacecraft is in an almost circular earth orbit, called "Earth Parking Orbit" (EPO). Now the postorbital insertion checks have to be done.

Time

Procedure

Panel

Remarks

00:12:00

Postorbital insertion checks

EDS PWR - OFF

MAIN BUS TIE (2) - OFF

SECS PYRO ARM (2) - SAFE

SECS LOGIC (both) - OFF

cb SECS ARM (2) - open

TRANS CONT PWR - OFF

ROT CONTR PWR DIRECT (2) - OFF

BMAG MODE (3) - RATE 2

LV STAGE sw - OFF (verify)

DIRECT O₂ vlv - CLOSE

C/W NORM - NORM

FC REACS VLVS - NORM

H₂ PURGE LINE HTR - ON



7
5
8


1


2
7

2

3

Prepares the FC purge check.

SM RCS monitoring check

SM RCS monitoring check

SM RCS PRPLNT tb (8) - gray

SM RCS HELIUM 1/2 tb (8) - gray

2

CWS operational check

C&WS operational check

A more detailed check is in the Caution and Warning System (CSM)

2

ECS post insertion config

ECS post insertion config

PRIM GLY EVAP STM PRESS ind -
	0.09-0.14 psi
PRIM ACCUM QTY ind - 25-50 %
RAD FLOW CONT PWR - PWR
PRIM GLY TO RAD vlv - NORMAL (push)
RAD PRIM HTR - 1
ECS RAD tb - gray
GLY EVAP TEMP IN - AUTO
POT H₂O HTR - MNA

2

325

2

CAB FAN (both) - on (up)
	O₂ FLOW ind - 1.0 lb/hr
	O₂ FLOW HI lt - on
	MASTER ALARM pb/lt - on, push

	O₂ FLOW HI lt - off
	PRIM GLY EVAP OUT TEMP ind - 38-43 °F
	RAD PRIM OUT TEMP ind - below
		RAD PRIM IN TEMP ind

2

1

2

After a few minutes.

Fuel cell purge check

Fuel cell purge check

3

EPS monitoring check

EPS monitoring check

A similar check is in the Electrical Power System (CSM).

ECS monitoring check

ECS monitoring check

A similar check is in the Environmental Control System (CSM).

Secondary water-glycol loop check

Secondary water-glycol loop check

{{ #if: |=== SCS attitude reference check ===

SCS attitude reference check

DSKY

1

| }}

Extend docking probe

Extend docking probe

8

2

References

</biblio>

@@ Line 1: / Line 1: @@
-When it's possible, the '''original Apollo documentation''' is used for the checklists. Steps, which are not possible at the moment, are denoted in grey. Additionally there are checklists in Word file format in the Doc\Project Apollo - NASSP\Check List directory of your [[installation]].  Procedural steps in this section are presented in tabular form and in sequence they occure during the mission. The following is a detailed explanation of the columnar data presented in the tabulated lists:
-[[Image:Apollo_15_launch_checklist.gif|thumb|right|Apollo 15 launch checklist<cite>A15_LAUNCH_CHECK</cite>]]
-{| class="wikitable"
-|-valign="top"
-|'''Time'''
-|This column contains the mission time the procedure is to be done. Sometimes there's no fixed time when to do a procedure, in that case the time is left out.
-|-valign="top"
-|'''Procedure'''
-|The procedure is a group of steps or overall tasks involved in performing a complete function or operation. It often consists of controls the astronauts have to toggle or display readings that have to be checked. See [[CSM panels]] for more informations.
-|-valign="top"
-|'''Panel'''
-|The panel number of a particular switch or display for easier panel navigation.
-|-valign="top"
-|'''Remarks'''
-|Any useful comment. Please notice especially differences to the original function, bugs or other issues.
-|}
 At T+00:00:00 the Saturn launches automatically. The following tables show the historical launch sequence of Apollo 16<cite>AOH2</cite>, all other Saturn V missions are very similar. Only the Saturn 1b missions are different, because the Saturn 1b stage has only 2 stages, so there's only 1 staging event.
-{{ #if: {{{VirtualAGC|}}} | | {{Attention | message=Please note that all DSKY interaction mentioned in the original documentation cannot be used in ''Standard mode'' with the NASSP AGC. }}
+{{ #if: {{{VirtualAGC|}}} | | {{Attention | message=Please note that all DSKY interaction mentioned in the original documentation cannot be used in ''Standard mode'' with the [[Simple AGC]]. }}
 }}
@@ Line 42: / Line 23: @@
 [[Image:Checklist_launch_boost9.gif]]
-{{ #if: {{{VirtualAGC|}}} | | {{Attention | message=Please note that all DSKY interaction on the last 2 pages above cannot be used in ''Standard mode'' with the NASSP AGC. With the NASSP AGC just enter V37 N00E to go to program P00.}}
+{{ #if: {{{VirtualAGC|}}} | | {{Attention | message=Please note that all DSKY interaction on the last 2 pages above cannot be used in ''Standard mode'' with the [[Simple AGC]]. With the [[Simple AGC]] just enter V37 N00E to go to program P00.}}
 }}
 == Postorbital insertion checks ==
@@ Line 258: / Line 239: @@
 </tr>
 <tr>
-<td>A more detailed check is in the [[CSM Caution and Warning System]]</td>
+<td>A more detailed check is in the [[Caution and Warning System (CSM)]]</td>
 </tr>
 </table></td>